When setting, the connecting joints of the vertical poles should be staggered.

The height of cuplock scaffold should be less than 20m, when the design height is greater than 20m, should be built according to the load calculation.Ĭuplock steel pipe scaffolding system column distance is 1.2m, longitudinal distance according to the scaffolding load can be 1.2m 1.5 m 1.8 m 2.4m, step distance is 1.8m, 2.4m. After all the joints are inserted, set the upper bowl button, and hit the convex head of the upper bowl button clockwise along the tangent line with a hammer, until the upper bowl button is fastened by the limit pin and no longer rotates. When setting up, first put the upper bowl button on the limit pin, insert the cuplock horizontal, cuplock brace diagonal and other joints into the lower bowl button, so that the arc surface of the joint is closely attached to the cuplock vertical. Joint setting: the joint is the connecting device of cuplock vertical with cuplock horizontal and cuplock brace diagonal, and should ensure that the joint is locked.

Cuplock scaffolding system strengthen transomĬommonly the length of cuplock scaffolding system strengthen transom is 800mm, 1300mm, 1800mm.All the above product sizes can be customized according to your actual needs.

Cuplock scaffolding system angle bracketĬommonly the length of cuplock scaffolding system angle bracket is 290mm, 560mm, 790mm.

Cuplock scaffolding system tube bracketĬommonly the length of cuplock scaffolding system tube bracket is 290mm, 560mm, 790mm.

Cuplock scaffolding system brace diagonalĬommonly tube size for cuplock scaffolding brace diagonal is 48.3*3.0mm.The length of cuplock system brace diagonal is 1500*1800mm, 1800*2000mm, 1500*2500mm, 2000*2500mm, 2000*3000mm.

Cuplock scaffolding system intermediate transomĬommonly tube size for cuplock scaffolding system intermediate transom is 48.3*3.0mm.The length of cuplock scaffolding system intermediate transom is 560mm, 800mm, 1300mm, 1800mm.

Cuplock scaffolding system ledger/horizontalĬommonly tube size for cuplock scaffolding system ledger/horizontal is 48.3*3.0mm.The length of cuplock system scaffolding ledger/horizontal is 600mm, 1000mm, 1500mm, 2000mm, 2500mm.

Cuplock scaffolding system vertical/standard spigotlessĬommonly tube size for cup lock scaffolding system vertical/standard spigotless is 48.3*3.2mm.The length of cup lock scaffolding system vertical/standard spigotless is 800mm, 1300mm, 1800mm, 2300mm, 3000mm.

The length of cup lock scaffolding system vertical/standard spigot is 500mm, 1000mm, 1500mm, 2000mm, 2500mm, 3000mm.

Cuplock scaffolding system vertical/standard spigotĬommonly tube size for cuplock system vertical/standard spigot is 48.3*3.2mm.

Nominal 2½ inches (2.Usually we will produce the cuplock products according to the size of the customer’s demand, before shipping will be sampled to measure whether the size meets the customer’s requirements.And the regular size of the cuplock system scaffolding is as follows: Nominal 2½ inches (2.375 inches) OD steel tube or pipe and a maximum post spacing of 6 feet x 8 feet. Nominal 2 inches (1.9 inches) OD steel tube or pipe and a maximum post spacing of 4 feet x 7 feet Nominal 2 inches (1.9 inches) OD steel tube or pipe and a maximum post spacing of 4 feet x 10 feet NOTE: Bearers must be installed in the direction of the shorter dimension. Nominal 2 inches (1.9 inches) OD steel tube or pipe NOTE: Longitudinal diagonal bracing must be installed at an angle of 45° (±5°).

Where conditions do not permit the attachment of bracing to posts, bracing must be attached to the runners as close to the post as possible.

Bracing must be installed as close as possible to the intersection of the bearer and post or runner and post.

On scaffolds whose length is less than their height, longitudinal bracing must be installed from the base of the end posts upward to the opposite end posts, and then in alternating directions until reaching the top of the scaffold.

On scaffolds whose length is greater than their height, longitudinal bracing must be repeated beginning at least at every fifth post.

Extend upward from the base of the end posts to the top of the scaffold at approximately a 45-degree angle.

Be installed diagonally in both directions.On straight run scaffolds, longitudinal bracing across the inner and outer rows of posts must :.Be installed at the bearer levels between the transverse bracing.Bracing must extend upward diagonally to opposite sides of the scaffold, such as from the inner posts or runners to the next outer posts or runners, or vice versa.Every third set of posts horizontally (measured from only one end).Transverse bracing forming an 'X' across the width of the scaffold must be installed at the scaffold ends, and at least at :.

Tube and coupler scaffold parts